Primaris Inceptors Stands - Alternative Rods Tutorial
Transcript
hello welcome everybody it is me Black Country wargaming and today I'm gonna be bringing you this alternative primaries in scepter basing tutorial so this is for anyone who doesn't like the plastic rods that come from Games Workshop and want something a bit alternative that you can use that he's going to be much more secure long-term this anyway here is the finished article and let's get into the tutorial to show you how I got to this stage so the first thing I use is a bit of a brass rod or welding rod whatever you want to basically use you can pick these up from anywhere my dad is a welder so he managed to pick up me a few of these from he's workplace now what you want to do is cut it down to between four and a half and five centimetres that's what I find the best length it doesn't have to be exact but that's they basically the best length I've found between four and a half and five centimeters then you just cut out a big massive pile of them depend on how many guys you have got to do I added to 12 so I have a big pile of these guys know what you want to do is find a drill bit that is round about the same size for your first pilot hole and then you want one that is just slightly a little
bit bigger so this here is a number one this is a one millimeter drill bit and I also use a one point two millimeter drill bit which is just slightly bigger when we get to that part and your first pilot hole you basically want to look under your 40 mil base you just want to drill a hole so you just want to drill a hole in either one it doesn't really matter which one you're gonna go for just drill a hole in your 40 mil base doesn't even have to be central in all on the stage just just drill the hole and then what you want to do is you want to get a little bit of cardboard so I've used cereal packet cardboard create a small little bit of card just underneath get a bit of superglue it doesn't have to be pristine and just blob it on there basically what this is gonna do is he's gonna prevent the brass rod when we feed it through from ever doing underneath the base and so when you move these guys around you're not constantly scraping the surface with the brass rod these acts like a little protection layer no no you want to do is drill out the hole so as it's now one point two just want to drill it slightly blow off all the excess and that won't feed this
through try it out to begin with don't put the superglue in there straight away just make sure it all feeds through and feeds through nicely then put a blob of superglue on feed this through the blob of the superglue so is it all sticks to the inside of there make sure it's straight and those it let's see here the flying stand done then and here is hominy I had to do myself as you can see there is slight bends but you can't avoid that unfortunately all you have to do is make sure it's as straight as possible and any kinks in the welding rod or brass rod will just make the model look a bit more active in a different position now for holes you want to drill a hole just underneath between both the vents here you're just trying to get your not point to drill just drill it straight in and you should feel a little release basically as you keep drilling your coop drilling through and then also in your drill will just seem to have nothing else left to drill and that is basically you find in the hollow part of the model sometimes there's not a hollow part of the model so just drill as far as you think you need to go it's all about knowing how
far to dig deep but it doesn't need to be that much you know all honesty just enough so as you know that the model will be secured in there then what I did was take my bit of brass rod welding rod and just stuck it in there and just wiggled it around so as it get a little bit of play just so as I know that it fits in some of these as well you cannot get to the underneath so you have to take this little sticking out past no idea what it is there's a little sticky out part here just underneath the oval part and I just drilled a hole straight through there I had two of those that were like this that was all I had but yeah you just can't get under this part here because of the leg obviously so you just have to go a little bit higher and drill straight in and there isn't much here at all in all honesty B once you find this this hole it will just as soon as you have like two or three drills just go straight through its Hollow and that in all honesty is that the second you've put these guys on there they will just fit in you don't need to glue them I done actually recommend gluing them unless you want them to be majorly secure but I would recommend just painting them as ease you know on a stay
and that way you can just easily remove these guys off the base if you want to I find it he's a little bit easier to paint them when it comes to these I have done some of these before exactly like this painting wise I find it a little bit easier to paint them if you can take them off but for spray-painting them I put them on the base and spray-painting them like this because then this you spray paint the brass rod well anyway guys have enjoyed this tutorial that is it I we find it useful and these flying stands much better than the plastic crap that comes from against workshop anyway guys I've enjoyed it and I shall see you in the next one